Skip navigation

Airsoft’s Powerburst

Revving Up RAS

Powerburst by Airsoft is a unique product. It's a remote-access accelerator. You can use it in both the Windows NT Server and Novell NetWare environments to speed interactions between a remote client and a file server. Powerburst improves performance by caching file accesses for the remote server. This approach means the client cache can handle subsequent accesses to a cached file so the server doesn't have to repeatedly retrieve the same file remotely.

Conceptually, this approach is similar to how the Netscape Navigator caches Web pages as you cruise the Internet. However, the big difference--and the big deal--is that Powerburst ensures the accuracy of the data in the cache before passing it to the requesting application.

In the Powerburst architecture, remote access breaks down into three logical functions, the file server, the client, and the agent. The file server can be a NetWare server or an NT Server. To access the file server, clients use a dial-in link such as NT Remote Access Service (RAS) or a router or similar remote connection. In the version of Powerburst we tested (1.20), no special software is required on the server.

The client is the user system that initiates the remote connection, or in the NT world, the client side of a RAS connection. Powerburst does most of its work on the client: After you establish your RAS link, you activate Powerburst, and it enables the client-based cache. In the NT Server environment, Powerburst 1.20 currently supports Windows 3.X and Windows for Workgroups (WFW) clients configured for RAS support. By the time you read this article, a version of Powerburst that also supports Windows 95 clients will be available. A timeline on planned support for Windows NT Workstation clients was not available at press time.

The agent is a special Airsoft-created function that validates data to ensure that the information in each client's cache is accurate and reflects the corresponding information on the file server. A single agent can concurrently handle up to 64 clients. In Powerburst 1.20, the agent software must run on a DOS-based system locally attached to the same LAN as the file server. By the time you read this, you can expect a new version of Powerburst that lets you run the agent as a virtual loadable module (VLM) under NetWare or as a service under NT.

The interaction between the client and the agent is the key to understanding Powerburst. On the client system, when you first start Powerburst, it begins building its cache of data as the client interacts with the remote file server. When an application requests data that exists in the cache, the client sends a terse, coded message to the agent. This message identifies the file in question and the data area in the file. The agent then uses a local, high-speed LAN connection to check the data on the file server and reports back to the client. If the data is unchanged, the request is satisfied from the local cache. Otherwise, Powerburst retrieves the data from the file server and refreshes its cache.

The assumption is that the client-query/agent-response approach is faster than retrieving the entire file over the remote connection. To further enhance performance, the client does look-ahead caching to predict future requests. In many ways, Powerburst's caching technique is similar to that of disk-caching programs, such as the DOS SMARTDRV program. The difference is that Airsoft has developed proprietary caching algorithms to address the unique characteristics of remote access.

The Test
We tested Powerburst 1.20 on a DOS-based 60-MHz Pentium system as the agent, a 60-MHz Pentium NT server as the file server, and a 50-MHz 486 laptop running WFW as the client. Powerburst came on two high-density disks: one for the agent and one for the client. The package included a thin, but fairly complete, manual.

The first decision was which protocol to use between the DOS agent machine and the NT server. Powerburst supports NetBIOS/NetBEUI and NetBIOS over TCP/IP in the NT environment. The DOS machine we used was already configured to run NetBIOS/NetBEUI with WFW, so we decided to take the path of least resistance. If WFW had not been on that machine, we could have installed DOS LAN Manager support from the NT Server distribution CD.

Installing the Powerburst agent software was simple and straightforward. After we installed it, we had to run a configuration program to define a name for the agent. The agent name is really the NetBIOS name that the clients use to establish sessions with the agent. Then, we rebooted DOS and brought up the agent by issuing three commands: netstartfull, share/l:500/f:5100, and pwragent

The netstartfull command activates WFW network support for DOS. The activation sequence prompts you for a username and password for your workgroup or domain. A critical requirement is that the username you specify has read access rights to all the files that the remote clients potentially will access.

The Powerburst agent software requires share /l:500 /f:5100. This is a DOS terminate-and-stay-resident (TSR) service.

The pwragent command invokes the agent, which runs as a foreground application. The agent software displays a brief configuration summary and then waits for an incoming client connection. This command doesn't establish a connection to the file server until a client connection is made.

With the agent up and running, our focus shifted to the client environment where we used WFW. A Windows-based setup program handles the installation of the Powerburst client software. This program copies the files to either a hard disk or a network disk. Then the setup program installs a new program group that contains Activate, Deactivate, Powerburst Control Panel, and Powerburst Helper applets. Finally, the program modifies the Windows system.ini file and the DOS config.sys file. (Powerburst wants files=100 and buffers=40.) You need to reboot when the installation process is complete.

Before you can use the Powerburst client software, you must configure the agent name you set up in the agent software. The client needs this name to communicate with the agent. The client-to-server RAS connection can use NetBIOS/NetBEUI or NetBIOS over TCP/IP. We used NetBIOS/NetBEUI.

Before you start the client software, you must use RAS to establish a link to the NT server and connect to one or more directories. If you attempt to start Powerburst before making these connections, you get a warning message saying that you don't have any remote file connections. After you connect to a directory, you activate Powerburst using the Activate icon or through the Control Panel. The Powerburst client then establishes a session with the Powerburst agent, displays confirmation of the end-to-end connection, and the caching process begins. Screen 1 shows the confirmation display.

Quick Cache?
The first time you run the Powerburst client, performance will be slower than usual because the client must build its cache, so that Powerburst can satisfy read requests from the cache--if the requested information is there. Information in the cache is delivered to the application about twice as fast as over the remote access link.

For a simple test, we loaded a 90KB Word for Windows document over a RAS link, with and without Powerburst enabled. First, we loaded the document with RAS to establish a baseline time. Then we enabled Powerburst with an empty cache to see how long loading the document and establishing a cache took. We loaded the same document again to see how the Powerburst cache affected the load time. Our tests took the following times (in seconds):

RAS only (Powerburst not enabled): 40.86

Powerburst enabled, no cache in place: 58.11

Powerburst enabled, accurate cache: 19.47

Loading the file from the Powerburst cache was approximately twice as fast as the initial RAS load. However, this was a best-case scenario. When we randomly added and deleted throughout the document, the client load time shot up to 46.38 seconds because most of the file needed to be reloaded. When we significantly changed only the second half of the file and then only the last fourth, the load time stayed in the same neighborhood--51.87 seconds and 46.93 seconds. The extent of changes didn't make much difference in the reload time.

In all fairness to Powerburst, focusing a test on the loading of a single, stream-oriented file is not a reflection of real-life performance. In real life, you work with a variety of files with several application processes. However, this test clearly shows the best and worst that Powerburst offers. You won't get best-case--or worst-case--performance from all your remote-access applications. Real-life experience will fall somewhere between these extremes.

In the Right Direction
Does the fact that you won't get 100% performance improvement 100% of the time invalidate the usefulness of Powerburst? Not at all. With repetitive work using file-based applications such as Word for Windows, Lotus 1-2-3, Microsoft Mail, and dBASE over a remote link, this product will improve performance.

Even if you average only a 50% improvement, that's still a 50% advantage over a regular RAS link. Clearly, that's a step in the right direction.

Powerburst 1.20
System Requirements:
File server: LAN-based Windows NT Server 3.51 (all platforms) or Novell NetWare 3.X/4.X server
Powerburst client: 80386 or higher, Windows 3.X or Windows for Workgroups, 4MB of RAM, 16MB of free disk space
Powerburst agent: Dedicated Pentium system, DOS 5.0 (or higher), 1MB of RAM, 1MB of free disk space, a LAN adapter
Airsoft * 408-777-7500
Price: Evaluation kit (2 clients, 1 agent): $495; Agent license: $995; Client licenses: 5 users $645, 10 users $1190, 50 users $4950, 250 users $22,250, 500 users $39,500, 1000 users $59,000, 5000 users $245,000
Hide comments


  • Allowed HTML tags: <em> <strong> <blockquote> <br> <p>

Plain text

  • No HTML tags allowed.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.